To run a ping test, we’ll open the same command line and type ping (host) with (host) being the website you’re trying to connect to. You’ll get something like this (we’ll use veesp.com again as an example):

Pinging veesp.com [104.22.74.140] with 32 bytes of data:

Reply from 104.22.74.140: bytes=32 time=ms TTL=56
Reply from 104.22.74.140: bytes=32 time=ms TTL=56
Reply from 104.22.74.140: bytes=32 time=ms TTL=56
Reply from 104.22.74.140: bytes=32 time=ms TTL=56

Ping statistics for 104.22.74.140:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 1ms, Maximum = 2ms, Average = 1ms

As expected, Veesp is online and running. If you’re having problems it could be on a hop, which is when you’d use the traceroute utility.

MTR stands for “my traceroute” and displays the route that a connection to a particular system takes by providing a continuously updating display of timing data.

Because MTR provides an image of the route the traffic takes from one host to another, it is essentially a directional tool. The route built between two points on the Internet may vary greatly under different circumstance like the location and the routers that are located upstream. For this reason, it is a good idea to collect MTR reports in both directions for all the hosts that are experiencing connectivity issues.

Veesp Customer Support will often request MTR reports both to and from your server if you are experiencing networking issues. This is because, from time to time, MTR reports will not detect errors from one direction when there is still packet loss from the opposite direction.

sudo apt update
sudo apt install mtr

yum install mtr

You can download WinMTR here: https://sourceforge.net/projects/winmtr/files/latest/download

Generate MTR report using the following syntax:

[root@localhost ~]# mtr -rwn4 veesp.com

  HOST: localhost.localdomain  Loss%   Snt   Last   Avg  Best  Wrst StDev
  1.|-- 212.6.44.1             0.0%    10    0.7   0.7   0.7   0.8   0.1
  2.|-- 91.203.69.80           0.0%    10    0.6   0.9   0.6   3.3   0.8
  3.|-- 91.203.69.73           0.0%    10    1.3   1.2   1.0   1.5   0.1
  4.|-- 78.28.193.98           0.0%    10    1.4   1.5   1.3   1.6   0.1
  5.|-- 213.248.84.32          0.0%    10    0.9   1.0   0.9   1.1   0.1
  6.|-- 62.115.119.193         0.0%    10    2.2   1.8   1.3   3.9   0.8
  7.|-- 195.12.254.187         0.0%    10    2.0   1.9   1.5   2.4   0.3
  8.|-- 104.22.74.140          0.0%    10    1.0   1.0   0.8   1.1   0.1

Beyond simply seeing the path between servers that packets take to reach their host, MTR provides valuable statistics regarding the durability of that connection in the seven columns that follow.

Loss% column shows the percentage of packet loss at each hop.

Snt column counts the number of packets sent.

The next four columns Last, Avg, Best, and Wrst are all measurements of latency in milliseconds (e.g. ms). Last is the latency of the last packet sent, Avg is the average latency of all packets, while Best and Wrst display the best (shortest) and worst (longest) round trip time for a packet to this host. In most cases, the average (Avg) column should be the focus of your attention.

The final column, StDev, provides the standard deviation of the latencies to each host. The higher the standard deviation, the greater the difference is between measurements of latency. Standard deviation allows you to assess if the mean (average) provided represents the true center of the data set, or has been skewed by some sort of phenomena or measurement error. If the standard deviation is high, the latency measurements were inconsistent. After averaging the latencies of the 10 packets sent, the average looks normal but may in fact not represent the data very well. If the standard deviation is high, take a look at the best and worst latency measurements to make sure the average is a good representation of the actual latency and not the result of too much fluctuation.

The Style macro allows the use of CSS to style content. CSS describes how HTML elements should be displayed. https://www.adaptavist.com/doco/display/CFP/Style+Sheet

.home-banner {
                    background: #459df0;
                    color: #fff;
                    font-size: 20px;
                    padding: 20px;
                    }
                    .home-banner h2 {
                    color: #fff;
                    }
                    .title-box {
                    border: 1px none #459df0;
                    padding: 10px;
                    }
                    .title-box > h2 {
                    background: #459df0;
                    bottom: 10px;
                    color: #fff;
                    margin-left: -10px;
                    margin-right: -10px;
                    padding: 2px 10px;
                    position: relative;
                    }